About this archived opportunity

This is a COMBINED SYNOPSIS/SOLICITATION for commercial items prepared in accordance with the information in FAR part 12, using Simplified Acquisition Procedures found at (FAR 13), as supplemented with the additional information included in this notice.  This announcement constitutes the only solicitation; a written solicitation will not be issued.  PAPER COPIES OF THIS SOLICITATION WILL NOT BE AVAILABLE. This combined synopsis/solicitation SHALL be posted to SAM.gov. The RFQ number is (SPMYM426Q3119). This solicitation documents and incorporates provisions and clauses in effect through FAC 2025-06 October 1, 2025, and DFARS Change Notice 20251110. It is the responsibility of the contractor to be familiar with the applicable clauses and provisions.  The clauses may be accessed in full text at these address(s): https://www.ecfr.gov https://www.acquisition.gov/content/list-sections-affected http://www.acq.osd.mil/dpap/dars/change_notices.html The FSC Code is (4730) and the NAICS code is (332999). The Small Business Standard is 750 employees. This requirement is 100% Small Business Set-Aside. Evaluation criteria is Lowest Price Technically Acceptable (LPTA). PPIRS will be used to determine vendor responsibility.  Potential contractors will be screened for responsibility in accordance with FAR 9.104. Offerors are required to submit descriptive literature to show how their quotation meets the required specifications.  A technical spec sheet and proof of traceability are required to be sent with quote. Failure to provide this information may result in your quotation being determined technically unacceptable. Only one quote per vendor may be sent. DLA Weapons Support, Pearl Harbor requests responses from qualified sources capable of providing: Interested parties must fill out the required request for quote saved in the attachment section. It is titled, “SPMYM426Q3119 QUOTE FORM”. HOSE ASSEMBLY, 2.5” INNER DIAMETER X 50’ LENGTH; ASSEMBLY CONSISTS OF A RUBBER HOSE, MALE CAM & GROOVE ADAPTER X HOSE SHANK WITH INTERLOCKING CRIMP FERRULE 1ST END, FEMALE CAM & GROOVE ADAPTER X HOSE SHANK WITH INTERLOCKING CRIMP FERRULE 2ND END.INTERLOCKING CRIMP FERRULE 2ND END. HOSE IS TEXCEL GAMMA-TANK 300, PART NO. GTA30S1-2.5. UV & ABRASION RESISTANT HOSE WITH NITRILE TUBE AND NEOPRENE COVER, NON-SLIP, GRIP EXTERIOR SURFACE FOR SAFETY AND HANDLING. HELICAL WIRE REINFORCED. HOSE ENDS TO BE MALE AND FEMALE CAMLOCKS PT COUPLING P/N 25C SLII, ITEM 1290325L2 AND PT COUPLING P/N 25E, ITEM 1200525. END FITTINGS SHALL BE COUPLED TO THE HOSE WITH STAINLESS STEEL FERRULES, PT COUPLING C50SS. CAMLOCK ENDS MUST BE WRAPPED TO AVOID DAMAGE TO THE FITTINGS DURING SHIPPING. UTILIZE PADDING TO PREVENT THE FEMALE CAMLOCK ARMS FROM GOUGING ADJACENT HOSES. HOSE ASSEMBLIES MUST BE PACKED/PALLETIZED TO MEET OR EXCEED THE MINIMUM BEND RADIUS TO AVOID KINKS AND DAMAGE TO THE HOSE. FULLY ASSEMBLED, HYDRO TESTED TO 275 PSI. NO LEAKS, WEEPS, BULGES OR END FITTING SLIPPAGE ALLOWED. ** SEE ATTACHMENT 1 FOR SPECIFIC/ADDITIONAL REQUIREMENTS. ** HOSE ASSEMBLY, 2.5” INNER DIAMETER X 25’ LENGTH; ASSEMBLY CONSISTS OF A RUBBER HOSE, MALE CAM & GROOVE ADAPTER X HOSE SHANK WITH INTERLOCKING CRIMP FERRULE 1ST END, FEMALE CAM & GROOVE ADAPTER X HOSE SHANK WITH INTERLOCKING CRIMP FERRULE 2ND END. HOSE IS TEXCEL GAMMA-TANK 300, PART NO. GTA30S1-2.5. UV & ABRASION RESISTANT HOSE WITH NITRILE TUBE AND NEOPRENE COVER, NON-SLIP, GRIP EXTERIOR SURFACE FOR SAFETY AND HANDLING. HELICAL WIRE REINFORCED. HOSE ENDS TO BE MALE AND FEMALE CAMLOCKS PT COUPLING P/N 25C SLII, ITEM 1290325L2 AND PT COUPLING P/N 25E, ITEM 1200525. END FITTINGS SHALL BE COUPLED TO THE HOSE WITH STAINLESS STEEL FERRULES, PT COUPLING C50SS. CAMLOCK ENDS MUST BE WRAPPED TO AVOID DAMAGE TO THE FITTINGS DURING SHIPPING. UTILIZE PADDING TO PREVENT THE FEMALE CAMLOCK ARMS FROM GOUGING ADJACENT HOSES. HOSE ASSEMBLIES MUST BE PACKED/PALLETIZED TO MEET OR EXCEED THE MINIMUM BEND RADIUS TO AVOID KINKS AND DAMAGE TO THE HOSE. FULLY ASSEMBLED, HYDRO TESTED TO 275 PSI. NO LEAKS, WEEPS, BULGES OR END FITTING SLIPPAGE ALLOWED. ** SEE ATTACHMENT 2 FOR SPECIFIC/ADDITIONAL REQUIREMENTS. ** HOSE ASSEMBLY, 2.5” INNER DIAMETER X 50’ LENGTH; ASSEMBLY CONSISTS OF A RUBBER HOSE, MALE CAM & GROOVE ADAPTER X HOSE SHANK WITH INTERLOCKING CRIMP FERRULE 1ST END, FEMALE CAM & GROOVE ADAPTER X HOSE SHANK WITH INTERLOCKING CRIMP FERRULE 2ND END.INTERLOCKING CRIMP FERRULE 2ND END. HOSE IS TEXCEL GAMMA-TANK 300, PART NO. GTA30S1-2.5. UV & ABRASION RESISTANT HOSE WITH NITRILE TUBE AND NEOPRENE COVER, NON-SLIP, GRIP EXTERIOR SURFACE FOR SAFETY AND HANDLING. HELICAL WIRE REINFORCED. HOSE ENDS TO BE MALE AND FEMALE CAMLOCKS PT COUPLING P/N 25C SLII, ITEM 1290325L2 AND PT COUPLING P/N 25E, ITEM 1200525. END FITTINGS SHALL BE COUPLED TO THE HOSE WITH STAINLESS STEEL FERRULES, PT COUPLING C50SS. CAMLOCK ENDS MUST BE WRAPPED TO AVOID DAMAGE TO THE FITTINGS DURING SHIPPING. UTILIZE PADDING TO PREVENT THE FEMALE CAMLOCK ARMS FROM GOUGING ADJACENT HOSES